Telescopes and Telescope Accessories

More Information  · Images of Some Features Price $64.95 Shipping $12.95 List Price $85.95 Shipping Weight 7.4 lbs. Warranty 2 years

The Power Tank has all of these features:

• 7 amp hour rechargeable battery capacity (somewhat less if used in temperatures below 32 degrees F), enough for many hours of observing with most telescopes

• two 12 VDC cigarette lighter plug outputs for powering scopes and accessories, with sliding covers to keep them dirt- and debris-free when not in use

• separate recessed 3V, 6V, and 9V DC 5.5mm male pin jack outputs for powering accessories or recharging a cell phone at a star party (tip positive, ring negative, 1 amp maximum load), using a user-supplied cord

• an 8’ long DC power cord (the cord labeled C in the feature image below), with a cigarette lighter plug on one end for connecting to one of the cigarette lighter plug outputs on the Power Tank and a female 5.5mm pin jack plug for connecting to the 12V DC input on a Celestron telescope on the other end

• very, very bright 800,000 candle power built-in spotlight for scope setup/takedown and for finding your way across a dark field (definitely not for use at star parties if you want to preserve the dark-adapted vision of those still observing)

• a built-in flashlight for scope setup and takedown with a tethered detachable red lens cover to preserve your dark-adapted vision (too bright for reading star charts; a variable brightness LED flashlight is still best for that)

• separate on/off switches for scope power, red lens flashlight, and spotlight

• battery indicator lights that show the status of the battery – ON/ready to use; needs charging; charging; or OFF/fully charged

• an external 110V AC recharger for replenishing the Power Tank’s battery charge as many as 100 times or more; the two parts of the adapter for U. S. and Canadian use are labeled A in the feature image below (since Celestron products are sold world-wide, the Power Tank also includes AC adapter plugs for use in Europe and Asia, which are labeled B in the feature image below); the AC adapter can be used with any 100 to 240 volt 50/60 Hz AC power supply

• a molded-in carrying handle.

• a shoulder strap.

In addition to powering Celestron scopes, the 7 amp-hour Power Tank can also be used with 12V Meade scopes, including current LX200R models. However, a Meade #607 DC cord is needed to connect the Power Tank to a Meade 12V scope due to the difference between the sizes of the 12V DC input plug center posts on Meade and Celestron scopes. Because the Power Tank has a 12-volt DC output, it cannot be used with older Meade non-GPS LX200 scopes that require an 18V DC external power supply.

As with any rechargeable battery, the Power Tank will operate at full power until approximately 40% of its charge is left. The output voltage will then start to drop relatively quickly past this point. At 30%-35% of its full charge, the Power Tank may not have enough output voltage to successfully operate your various electronic components. The maximum true full power output capacity of the 7 amp-hour Power Tank is therefore in the neighborhood of about 4.5 to 5 amp-hours.

To calculate how long the 7 amp-hour Power Tank will operate your particular complement of equipment, add up the maximum amperage ratings of your telescope and telescope accessories. Divide 4.5 by the total amperage draw of all your components to find the worse case number of hours that this Power Tank will operate your system. Keep in mind that accessories will usually not operate continuously at their full rated amperage. A dew heater might be rated at a 1-amp draw, but that is when it is turned up to maximum power. Seldom are dew heaters turned on full and left at that setting. Operating at only 1/4 to 1/3 of the rated power is usually more typical. The actual operating time of the Power Tank on a single charge can therefore often be two to three times the length of the worst-case scenario calculated above. Your operating time will depend on the ambient temperature and the particular combination of components you are using.

A note on assembling the AC adapter: The AC adapter has two parts, the adapter itself, and the prong assembly that snaps into the adapter and plugs into your 110/120VAC household wall socket. Do not attempt to slide the prong assembly straight into the adapter! This will cause damage to the adapter that is not covered by warranty.

Refer to the feature images below for proper assembly. Note that the metal prongs of the prong assembly are placed at the opposite end of the adapter from the end with the cord connected to it. The prong assembly is placed on top of the AC adapter so that tabs on the prong assembly can drop into small slots in the sides of the long and wide slot of the AC adapter. When the tabs drop into the slots and the top of the prong assembly is flush with the top of the AC adapter, slide the prong assembly into the AC adapter in the direction of the arrow in the image until the prong assembly clicks into place.

You should not have to remove the prong assembly unless you move overseas and need to connect your Power Tank to a different type of AC outlet. The prong assembly can be removed from the adapter by using a pencil to push down on the tab in that adapter that locks the prong assembly in place.

The battery instructions caution against using the charger continuously for more than 24 hours to avoid overcharging the battery and possibly damaging it. In addition, the instructions suggest recharging the battery occasionally to maintain its performance if it is not going to be used for several months at a time.

Printed instructions are supplied with the Power Tank. If all else fails, read the instructions!