Feather Touch 2" Manual Crayford focuser for SCTs - with 0.8" drawtube travel


Availability: More on the way

This Crayford-type 0.8" travel Feather Touch 2" focuser is precision-machined for use with Schmidt-Cassegrain telescopes. The friction-drive focuser's zero image shift/no backlash design is a must for critical CCD imaging and astrophotography . . .
Our Product #: FT-0.8BC
Starlight Instruments Product #: FTF2008BCR

Product Description

This 0.8" travel Feather Touch low profile 2" focuser from Starlight Instruments is a precision-machined premium Crayford-type focuser for catadioptric telescopes. In addition to making visual observing a precision joy, the friction-drive focuser's zero image shift/no backlash design is a must for critical CCD imaging and astrophotography. It totally eliminates the image-shift inherent in any telescope that moves the primary mirror to focus.

Optional mounting base adapters are available for installing the focuser on catadioptric rear cells as well as on reflector optical tubes and truss-tube Dobsonian secondary mirror cages. (A base adapter is required in all cases for installing the focuser on a telescope.) Non-vignetting short adapter #FT-MSLG for Meade 10" and larger scopes will generally let the focuser swing through the fork arms of these particular SCTs. Mounting base adapters #FT-SCT for 7" through 9.25" Celestrons and Meades, #FT-CLG for 11" and larger Celestrons, and #FT-MLG for 10" and larger Meades have enough internal length to allow the long drawtube travel of this focuser to be used. However, they typically will not allow the focuser to swing through the fork arms of the smaller aperture scopes, depending on the length of the accessory stack attached to the focuser. German mount SCT scopes do not have this potential swing-through problem and the focuser can readily be used with any base adapter.

Drawtube travel is 0.8" to allow the focuser to swing through the fork arms of a 10" or larger catadioptric scope when used with one of the short SCT adapters. The focuser body is 1.6" tall, exclusive of mounting base. Adding a short SCT adapter increases the focuser body height to only 2.7" tall. With drawtube fully extended, the top of the drawtube is 3.3" above the focuser base.

The 2" eyepiece holder uses a soft brass compression ring to hold 2" eyepieces and the optional Easy-Grip zero length 1.25" eyepiece adapter (#FT-ADEP). This non-marring design will not scratch the chrome barrels of your eyepieces, as a conventional thumbscrew eyepiece holder can. The compression ring also has improved holding power over conventional thumbscrews, even nylon-tipped screws. There are two thumbscrews on the draw tube. One is used for 2" eyepieces; the other for 1.25" eyepieces when using the #FT-ADEP 1.25" adapter.

All running parts are polished stainless steel for durability and wear resistance. Its floating hardened stainless steel raceways are matched to stainless steel ball bearings for improved smoothness over conventional Crayford focusers. The result is a drawtube that moves with a buttery smoothness and zero backlash. This steel-on-steel running gear design will virtually never wear out or degrade with age or use. The hardened stainless steel drawtube friction plate likewise will not wear out as will the softer aluminum plates used in lesser focusers.

There are coarse and fine focus knobs with a 10:1 reduction ratio for unrivaled accuracy and repeatability. Each revolution of the fine focus knob results in a mere 0.070 inches of drawtube travel, making critical focus effortless. Fine focus repeatability is on the order of <0.0005 inches. The lifting capacity is nominally adjustable up to five pounds, although greater payloads are possible by adjusting the drawtube friction using the built-in brake.

Because the focuser is so smooth in operation and moves so freely, it can only hold a limited amount of weight (generally about 1 lb.) without drifting out of focus when the focuser drawtube is not horizontal and has a vertical component. The focuser therefore contains an adjustable tension internal brake system to allow astrophotography and visual use with heavy eyepieces without the possibility of the focus shift.

The brake consists of a lever arrangement internal to the pinion block. Adjusting the thumbscrew on the pinion block causes the lever to press a friction pad onto the pinion. This increases the torque needed to turn the focus knobs. If the thumbscrew is turned all the way in (generally only 1 to 1½ turns), the pinion shaft and the drawtube are locked in position for long exposure astrophotography. Visually, partial tightening of the internal brake offers a virtually infinite range of braking force to accommodate various eyepiece weights.

A letter to Starlight Instruments from Jack Newton, well-known astrophotographer, said,
    "I have just installed your zero backlash Feather Touch Focuser on my Meade 16-inch telescope. This focuser is the finest I have ever used! It is built with the precision of a Swiss watch. Your superb workmanship has produced a focuser in a class by itself.
    "I attached a dial micrometer to measure the focus differential required for demanding CCD tri-color imaging and cannot get over the smooth performance of this incredible instrument. My Pictor 1616XT and a large filter wheel have a combined weight of over 7 pounds. Even bearing this heavy load, the focuser moves with micrometer precision.
    "Thanks, Starlight Instruments, for this wonderful contribution to my CCD focusing!"

Tech Details

Weight 16 oz.
Warranty 1 year


Review by:
If you have never used a feathertouch focuser you should start. If you're doing AP this is indispensable. the standard Celestron focuser is fine for visual, but doesn't provide the micro-fine focus needed for Astrophotography. Even for visual, the ability to be able to focus in micro-increments on Saturn without it jumping all over the place was worth every penny. The ability to get into razor sharp focus was important to me (especially for AP)and without a microfocuser it was near impossible to achieve this unless i just got lucky. We all know how little time we get to image and so much AP i see is amazing, but a hair out of focus at times. just my 2 cents, but a good quality microfocuser is as important as a good mount in terms of your images. if you can track and have a good camera and optics but cant get the sharp focus you need, its all for naught... in the end, in AP, its Tracking, Focus and optical quality of your scope that make an image a winner. The feathertouch focusers are legend among Astronomy enthusiasts... Get one (Posted on 12/21/2018)
How do you rate this product? *